• Quantity:
Total: to quote
Cart is empty.

International Antifouling Uni-Pro EU Red 5Lt #458COL1150

International Antifouling Uni-Pro EU Red 5Lt #458COL1150
You Save:
€240.39 (57%)
Combination not available


5 litre Pack. Red colour.


Universal antifouling designed for sailing boats and power boats (up to 25 knots).

* Season long antifouling protection in all but the harshest fouling conditions
* Simple standardised surface preparation
* Compatible with the majority of antifouling schemes


Colour YBB820-Dover White, YBB821-Red , YBB822-Blue, YBB823-Navy, YBB824-Black
Finish Matt
Specific Gravity 1.8
Volume Solids 60%
Typical Shelf Life 2 yrs
VOC (As Supplied) 351 g/lt
Unit Size 5 lt, 20 lt


5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Touch Dry 1 hrs 45 mins 30 mins 20 mins
Immersion 24 hrs 10 hrs 4 hrs 4 hrs
Note: Max. Immersion Times are as follows: 5-35°C - 6 mths
Substrate Temperature
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Uni-Pro EU 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext



In Good Condition Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition Use Interstrip to remove all traces of antifouling.

PRIMING All preparation for bare substrates is covered on the appropriate primer labels.

BARE GRP Gelshield 200 for osmosis protection, or Primocon.

STEEL/IRON Interprotect or Primocon.

LEAD Interprotect or Primocon.

WOOD Prime with Interprotect or Primocon.
Hints Mixing Stir well before use.
Thinning Thinning is not recommended.
Cleaner YTA085 Thinners No.3
Ventilation and Humidity Control Ensure adequate ventilation during use.
Airless Spray Pressure: 176-210 bar. Tip Size: 2180. SPRAY APPLICATION - PROFESSIONAL APPLICATORS ONLY.
Other For Airmix spray application - Pressure: 2.5 bar. Tip Size: 20-113. True colour will develop after immersion. Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness.
Some Important Points To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 1°C above dew point and maximum 35°C.
Compatibility/Substrates GRP, Wood, Steel/Iron, Lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Can be applied direct over most types of antifoulings, provided they are in sound condition Number of Coats Apply 2 coats per season by brush, 1 coat per season by spray.
Apply an extra stripe coat in areas of high wear such as chines, rudders, sterngear and any leading edges.
Coverage (Theoretical) - 10 m²/lt per coat by brush, 5 m²/lt by spray(Practical) - 9 m²/lt per coat by brush, 3 m²/lt by spray
Recommended DFT per coat 60 microns dry by brush / roller, 120 microns dry by spray
Recommended WFT per coat 100 microns wet by brush / roller, 200 microns wet by spray
Application Methods Airless Spray, Airmix, Brush, Roller



Exposure to air and extremes of temperature should be avoided. For the full shelf life of this product to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight.


Uni-Pro EU should be kept in securely closed containers during transport and storage.


Contains biocides. Antifoulings should only be wet sanded. Never dry sand or burn-off old antifoulings. Read the label safety section for Health and Safety Information, also available from our Technical Help Line.


Remainders of Uni-Pro EU cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.
Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.

IMPORTANT NOTES The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further written enquiries as to the suitability of the product for the intended purpose does so at their own risk and we can accept no responsibility for the performance of the product or for any loss or damage (other than death or personal injury resulting from negligence) arising out of such use. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.