• Quantity:
Total: to quote
Cart is empty.

International Micron Antifouling Premium WA Multiseason 2,5 Lt Dark Blue YBC203 #458COL557

International Micron Antifouling Premium WA Multiseason 2,5 Lt Dark Blue YBC203 #458COL557
You Save:
€192.60 (55%)
Combination not available


Micron WA (Professional) Antifouling Water Activated Matrix technology.

2.5 litre Pack. Dark Blue YBC203 colour.

Incorporating unique Water Activated Matrix technology, Micron WA (Professional) is a premium antifouling that provides outstanding multi-season antifouling protection, even in high-challenge areas
- Water Activated Matrix technology - powerful antifouling protection against all types of fouling, in all types of waters
- Vibrant colour and uniform appearance - develops when immersed to provide a striking, attractive finish
- Very low VOC helps owners and boatyards to reduce their environmental impact and meet local regulations
- Water based formulation - facilitates quick and easy clean up, low odour and low fume emissions providing a pleasant, safe environment
- For professional use only.

Colour YBC200-White, YBC201-Blue, YBC203-Navy, YBC204-Red, YBC205-Black
Finish Matt
Specific Gravity 2
Volume Solids 37%
Typical Shelf Life 2 yrs
VOC (As Supplied) 3 g/lt
VOC (EU Solvent) 2 g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC)

In Good Condition Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with
In Poor Condition Use Interstrip to remove all traces of antifouling.
PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON Interprotect or Primocon.
LEAD Interprotect or Primocon.
WOOD Interprotect or Primocon.
Hints Mixing Shake or stir thoroughly before use, using a wooden or plastic stirring stick. Leave to stand for 10 minutes for air bubbles to disperse.
Thinner Thinning is not recommended.
Airless Spray Pressure: 1500 psi. Tip size: 519.
Other Antifoulings should only be vacuum sanded or wet sanded. Never burn-off old antifoulings. True colour will develop after immersion. To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide.
Cleaner Clean equipment immediately after painting using fresh water. Once paint has dried, clean equipment using YTA085 Thinners No. 3.
Some Important Points:
* Upon application, Micron WA (Professional) dries to a finish that is unlike a conventional antifouling. It may appear matt,
with colour variations or unevenness caused by different rates of water evaporation (depending on the condition of the
underlying substrate). However, a uniform finish and bright, vibrant colour will develop upon immersion
* Colour residue can be rubbed from the surface, even when dry for several days. This is the nature of the product and
does not mean that the coating is not dry
* Some colour may wash off from the paint when high pressure fresh water washed
* Do not apply when raining or if rain is imminent
* Do not apply between tides
* Care must be taken to ensure adequate ventilation is provided for sufficient drying conditions
Compatibility/Substrates GRP, Wood, Steel/Iron, Lead.
Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Can be applied direct over most types of antifoulings, provided they are in sound condition Micron WA (Professional) cannot be applied direct to GRP. If applying to GRP, apply Gelshield 200 or Primocon beforehand. Refer to relevant datasheet.
Number of Coats By brush/roller, 2 coats for one season's performance and 3 coats for two seasons' performance when the recommended DFT is applied.
By airless spray, 2 coats for up to two seasons' performance when the recommended DFT is applied.
Apply an extra stripe coat in areas of high wear such as chines, rudders, sterngear and any leading edges.
Coverage (Theoretical) - 9.17 m²/lt by brush/roller, 6.10 m²/lt by spray
(Practical) - 8.3 m²/lt by brush/roller, 3.66 m²/lt by spray
Recommended DFT per coat 40 microns dry by brush / roller, 61 microns dry by spray
Recommended WFT per coat 108 microns wet by brush / roller, 165 microns wet by spray
Application Methods Airless Spray, Brush, Roller


Exposure to air and extremes of temperature should be avoided. For the full shelf life of this product to be realised
ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F. Keep
out of direct sunlight.
The product should be kept in securely closed containers during transport and storage.
Contains biocides. Use biocides safely. Antifoulings should only be vacuum sanded or wet sanded. Never burn-off old antifoulings. Correct PPE must be worn during application. Although equipment can be cleaned with water, the
contaminated water must not be allowed to enter water courses. Always read the label and product information before use. Read the label safety section for Health and Safety Information, also available from our Technical Help Line.
Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.
Remainders of this product cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.
IMPORTANT NOTES The information given in this sheet is not intended to be exhaustive. Any person using the product without first making
further written enquiries as to the suitability of the product for the intended purpose does so at their own risk and we can accept no responsibility for the performance of the product or for any loss or damage (other than death or personal injury resulting from negligence) arising out of such use. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.